In this article, we’ll delve into how to do a service light reset for vehicles where there is a manual process to this action. We’ll guide you on what it is and how it’s done for common car models here in Australia.

So you’ve done the service maintenance on your car all by yourself. You’re so proud, happy that you’ve accomplished this task and you’re also happy you saved hundreds of dollars in labour cost. But your service indicator light is still on? How do you reset this? 

service light reset
Sample service light warning

What is a service light reset?

Your service lights serve one important purpose: to tell you that your car needs servicing in the next so many KM as set by the manufacturer. That is plenty of time to prepare for the next car service by your friendly, neighbourhood mechanic or by you (aka Do-It-Yourself). After servicing, the service light needs to begin the countdown again for the next round of car maintenance.

By doing regular car servicing, you not only save money on unplanned car repairs and parts replacement. You also preserve a high resale value for your car, increase fuel economy, and will keep you and your passengers safe from unwanted breakdowns that can cause loss of time and a cost to get the car back to where it needs to go if you need to tow it. It is a short-term cost for a long-term benefit.

Can you reset all cars manually? Or do I need some tools?

On most cars, you just need to follow the car’s manual or read articles such as this, and you can do the reset in no time. There are times, though, that you will need some OBD tools to do it.

But first, check if your vehicle is OBD1 or OBD2. Once you’ve determined this, you will need a scan tool to do the entire process. 

In simple terms, a scan tool or diagnostic tool determines faults in your vehicle and helps you clear them if needed. You can purchase the basic or full system scan tool as both can do the service light reset. Your choice may just come down eventually to how in-depth you need to check your car’s system. 

Service light reset

If you still have trouble with your service lights, or you need someone to consult regarding scan tools, we at OBD2 Australia will gladly answer your concerns as best as we can!

Service Light Reset Guide

Here is a list of vehicles and their reset guides. This does NOT cover all vehicles in Australia and all the models per brand. We will update this post to include other vehicle models as we can. Bookmark our website now so you can keep track!

BMW

E70 Service Light Reset

  1. Put the ignition key in its slot.
  2. Do not start the engine. Press the Start|Stop button once, and see all the lights in the dash come on as a cluster. Do not put your foot on the brake. 
  3. Make sure the doors are closed and there are no warnings showing on the dash.
  4. If there are warnings, push the end of the left stalk until the main screen is showing in the cluster. Push and hold the left button until it shows a service item to reset.
  5. Once you see the picture of the front brakes or rear brakes, push and hold the button until it says RESET.
  6. Repeat procedure for rear pads.

E46 E39 Service Light Reset

  1. Turn the ignition to the 0 position
  2. Press and hold the trip meter button and turn the ignition key to position 1.
  3. Press and hold the button for approximately 5 seconds until you see OIL SERVICE or INSPECTION with RESET or RE displayed on the screen.
  4. Again, press and hold for about 5 seconds. The words RESET or RE will then flash on the screen.
  5. While the display is flashing, press the button briefly to reset the service interval.
  6. After the display has briefly shown the new interval, it will change the brake fluid renewal interval reset.
  7. The CLOCK SYMBOL will then appear on the display.
  8. Press the button briefly to skip the brake fluid renewal interval reset menu. END SIA will display for approximately 2 seconds.

Chrysler

Grand Voyager 2000 to 2008 Service Light Reset

  1. Switch the ignition ON
  2. Press the menu reset button until you see the service interval displayed
  3. Repeatedly press the step button to set the distance to the next service
  4. Press the C/T button until the display changes
  5. Tap the step button until you see YES displayed.
  6. Press the C/T button and switch ignition OFF

Ford

Fiesta & Mondeo Service Light Reset

  1. Turn ignition key to ON position II
  2. Press brake and accelerator pedals together for 15-20 seconds
  3. Service interval indicator will flash when reset is complete
  4. Release pedals and turn ignition OFF

Transit Service Light Reset

  1. Turn ignition key to position II
  2. Press brake and accelerator pedals together for 15-20 seconds
  3. Service interval indicator will flash when reset is complete
  4. Release pedals and turn ignition OFF

Falcon Service Light Reset

  1. Turn ignition on
  2. Press trip meter reset button for 12 seconds
  3. You should hear a beep & the light should go out.

Ranger 2006 to 2012 Service Light Reset

  1. Turn off the ignition.
  2. Close all doors.
  3. Turn the ignition key to position II. If your vehicle has push-button start, press and hold the “Start” for two seconds without touching the brake pedal.
  4. Next, simultaneously press the accelerator pedal and the brake pedal and hold for a minimum of 20 seconds. Wait until a “Service: Oil reset in prog.” message shows on the instrument cluster display.
  5. Continue holding the gas and brake pedals until the display says “Service: Oil reset complete”.
  6. The oil change reminder indicator will turn off.

Ranger 2013 to 2019 Service Light Reset

  1. Turn the ignition to ON.
  2. Use the directional pad on the steering wheel and scroll through the settings area under the heading menu.
  3. Go to Settings > Vehicle > Oil Life Reset.
  4. Push and hold OK until it resets to 100%
  5. Turn off the ignition and then restart the engine to verify the reset was completed.

Focus 2000 to 2018 Service Light Reset

  1. Turn on the ignition (or push the start button with the clutch up). Don’t Start the Engine.
  2. Press the brake and accelerator fully down.
  3. After a moment, the centre display will tell you that the reset is in progress.
  4. Keep the pedals down until it informs you that reset is complete.

Holden

Astra (Early) Service Light Reset

  1. Press and hold trip reset button
  2. Switch ignition ON
  3. The letters “INSP” will appear in the display for 2 seconds
  4. Keep trip reset button depressed until ”—-” appears in the display.
  5. Release trip reset button
  6. Switch ignition OFF

Astra (Late) Service Light Reset

  1. Press and hold trip reset button
  2. While holding trip reset button, press on the brake pedal
  3. Keep holding down brake pedal and trip reset button and turn ignition to ON
  4. Keep holding both for about 5 seconds
  5. The “—-” symbol should appear when reset is complete
  6. Switch ignition OFF

Barina Service Light Reset

  1. Turn ignition to position I
  2. Depress the trip reset button next to tacho a few times until you see an oil can image on the display
  3. Once an oil can is displayed, hold down trip button until 100% is shown
  4. Switch ignition to OFF

Captiva Service Light Reset

  1. Turn ignition ON
  2. Within 5 seconds, press the accelerator pedal 3 times
  3. Check if the oil light has been reset

NOTE: Make sure you close all doors, boots, and bonnet.
Repeat procedure if first attempt fails

NOTE: DIESEL – Only do this reset after an oil change is performed. It resets the counter for DPF forced regenerations. If you do this without changing the oil, you risk getting the oil too diluted with diesel. This can damage the engine

RC Colorado Service Light Reset

  1. Turn ignition ON
  2. Keep pressing the trip reset button until the OIL LIFE message is displayed
  3. Once the OIL LIFE and RESET messages appear on the display, press and hold the reset button until several beeps sound.
  4. Turn the ignition OFF

VX Commodore Service Light Reset

  1. Switch ignition OFF
  2. Press and hold the up and down buttons
  3. Switch ignition ON
  4. Keep buttons depressed until “RESET” starts flashing
  5. Release the up and down button
  6. Repeatedly press the mode button until the service message is displayed
  7. Press and hold up and down buttons until a beep is heard
  8. Release up and down buttons
  9. Switch ignition OFF
  10. Switch ignition ON

VY & VZ Commodore Service Light Reset

  1. Switch ignition OFF
  2. Press and hold up and down buttons
  3. Switch ignition ON
  4. Wait 3 seconds
  5. Release up and down buttons
  6. Press and hold set button
  7. There will be an audible signal when the reset is complete
  8. Display will now read “Service Reset No Items”
  9. Release the set button
  10. Switch ignition OFF

VE Commodore Service Light Reset

  1. Switch ignition OFF
  2. Press and hold trip button on steering wheel
  3. Switch ignition ON
  4. Release trip button
  5. The message “SERVICE RESET” will appear in the cluster centre display
  6. Press and hold the scroll wheel until the display clears and you hear an audible signal
  7. Switch ignition OFF

VF Commodore Service Light Reset

  1. GM Oil Life System Resetting (Australia and South Africa Service Reminder)
  2. Change Engine Oil Soon ‘service reminder’ message appears in the instrument panel centre.
  3. This message is triggered every 14,000 km from when last reset, and is therefore not the same as Oil Life Monitoring. Oil Life Monitoring is switched off for Australian and South African vehicles.
  4. Service Reminder Reset Procedure
  5. Service Reminder message is reset using the global service tool or manually by the technician by switching ignition on and pressing the accelerator pedal 3 times.

JH Cruze Service Light Reset

  1. Turn ignition to ON
  2. Continue to press the menu button located on the indicator stalk until the remaining oil life percentage is displayed on the info screen
  3. Press SET/CLR button on the end of the indicator stalk and press the brake pedal at the same time
  4. When completed, the remaining oil life should display 100%

Jaguar

XF Service Light Reset

  1. Switch ignition OFF
  2. Press and hold the rear fog lamp button.
  3. Switch ignition ON
  4. Release fog lamp button
  5. Press and hold trip button (left stalk)
  6. Press and hold rear fog lamp button.
  7. Hold the button for 10 seconds
  8. Release the button
  9. Switch ignition OFF

Land Rover

Evoque Service Light Reset

  1. When ‘Service Due’ shows on the dash, use the right steering control to scroll through the options.
  2. Press RIGHT to open menu.
  3. Scroll down to ‘SERVICE MENU’
  4. Enter ‘SERVICE MENU’, scroll down to ‘LAST ALARM STATUS’
  5. Press ‘DOWN’ Button on right steering wheel control and ODO reset simultaneous for 15 seconds
  6. Cycle ignition

Mercedes

C Class Model 203 Service Light Reset

  1. Turn ignition on
  2. Press system selection button (S110s3) repeatedly until the basic display “kilometer reading or temperature display” or “speed display” is shown in the multi-function display (A1p13)
  3. Briefly press the instrument illumination brightness control and reset button (A1r1) 3 times. An acoustic signal can be heard, and the voltage is shown in the multi-function display (A1p13).
  4. Turn ignition to position 2
  5. Press the lower scroll forward/back button (S110s1). “Service indicator” should appear in the multi-function display (A1p13).
  6. Press the instrument illumination brightness control and reset button (A1r1) once briefly. The menu “Oil type”, for selecting the specification of the engine oil used, appears in the multi-function display (A1p13).
  7. Select the engine oil grade used by pressing the + and – buttons, setting of specific functions and volume control (S111s1) for vehicles with spark ignition engine and oil selection.
  8. Press the upper scroll forward/back button (S110s1) to confirm. “Confirm oil reset, press R button for 3 seconds” when it appears in the multi-function display (A1p13).
  9. Hold down instrument illumination brightness control and reset button (A1r1) for 3 seconds. “Service confirmed” should appear in the multi-function display (A1p13).
  10. Press the upper scroll forward/back button (S110s1). “Service indicator” should appear in the multi-function display (A1p13).
  11. Press the upper system selection button (S110s3). The basic display “kilometer reading”, “temperature display” or “speed display” should appear in the multi-function display (A1p13).
  12. Turn ignition off.

E Class Model 211 Service Light Reset

  1. Turn on ignition
  2. Press the button (S110s3) repeatedly until the basic display “kilometer reading” is shown on multi-function display
  3. Briefly press the trip odometer reset button (A1s3) 3 times.
  4. Press the lower scroll forward/back button (S110s1). “Service menu” should appear in the multi-function display.
  5. Press the “+ and -” buttons that sets specific functions and controls volume (S111s1) repeatedly, and select the “Confirmation” menu item.
  6. “Confirmation” appears in the multi-function display (A1p13) and the menu item “Complete service” is highlighted once you press the lower system selection button (S110s3) to confirm.
  7. Press the lower system selection button (S110s3) to confirm. “Service confirmed” should appear in the multi-function display (A1p13).
  8. Press the top system selection button (S110s3) repeatedly until the “Service menu” is shown in the multi-function display (A1p13).
  9. Using the “+ and -” buttons that sets of specific functions and controls volume (S111s1), select the menu item “Special work”.
  10. Press the lower system selection button (S110s3) to confirm.
  11. Using the “+ and -” buttons that sets of specific functions and controls volume (S111s1), select menu item “Service 13”.
  12. Press the lower system selection button (S110s3) to confirm.
  13. Select the engine oil grade to be used by pressing the “+ and -” buttons that sets specific functions and controls volume (S111s1) for vehicles with spark ignition engine and oil selection.
  14. Press the lower system selection button (S110s3) to confirm. The message “Position confirmed” should appear in the multi-function display (A1p13).
  15. Press the upper system selection button (S110s3) repeatedly until the basic display “kilometer reading”, “temperature display” or “speed display” is shown in multi-function display (A1p13).
  16. Turn ignition off.

Nissan

Navara D40 2013 Service Light Reset

  1. Turn ignition on.
  2. Within 5 seconds push odometer reset Button (right). 
  3. Then push button until the service mileage is correct.

NOTE: If spanner with “0” is flashing, press both buttons at once

Xtrail Service Light Reset

  1. Turn the ignition “ON”.
  2. Press the back button twice until you see “SETTINGS” displayed on the dashboard. If you have trouble finding the back button, it is on the top right-hand side of your steering wheel. 
  3. Select “SETTINGS” and press “ENTER” to confirm.
  4. Press the “ENTER” button up or down until you find “MAINTENANCE”.
  5. Select “MAINTENANCE” and press “ENTER” to confirm.
  6. Press the “ENTER” button up or down again until you get to “SERVICE”. 
  7. Select “SERVICE” and press “ENTER” to confirm.
  8. Follow the prompts to reset. If no prompt is visible, press “ENTER”, and it should ask you if you want to reset. 
  9. Choose “yes” and press “ENTER” to confirm.

Pulsar Diesel/Petrol 2014 to 2019 Service Light Reset

  1. Turn the ignition key to position ONE without starting the engine, or if your Nissan Pulsar have Smart key button, press the START button twice without touching any pedal.
  2. Access the Setting menu on the cluster menu screen.
  3. Scroll down and highlight the Maintenance option and press ENTER
  4. Highlight the “Oil and Filter” and press ENTER
  5. Scroll down to highlight “RESET” and press ENTER
  6. Scroll down to “YES” and press ENTER

Volvo

C70 Service Light Reset

  1. Turn the key to #1.
  2. Press and hold the trip reset button while turning key to #2.
  3. Wait for the service light to flash.
  4. When the lamplight stops flashing (usually within 4 seconds), return the key to OFF and release trip reset button.

S40 MY2004 Service Light Reset

  1. Turn the key to Ignition position I.
  2. Press and hold the reset button for the trip odometer (usually around 2 seconds).
  3. Turn to Ignition position II.
  4. Press and hold the reset button for the trip odometer until the original value has been reset.
  5. The information lamp lights will show when you release the reset button.
  6. Release the reset button for the trip odometer within 4 seconds. The instrument will give an audible signal when resetting has succeeded. 
  7. If you do not release the reset button for the trip odometer within 4 seconds, the service reminder indicator (SRI) is not reset.
  8. If the trip odometer is already reset, hold the reset button for a minimum of 10 seconds and a maximum of 14 seconds.

S60 Service Light Reset

  1. Turn the ignition to ON position
  2. Hold the trip reset button then turn the ignition to position one and wait for one to two seconds.
  3. Turn ignition to position two. Keep the trip reset button pressed down.
  4. The service light will flash, but DO NOT let it flash over 4 times.
  5. Turn ignition off and remove the ignition key.

XC90 up to MY2001 Service Light Reset

  1. Turn key to Ignition position I.
  2. Press and hold the reset button for the trip odometer, then turn to Ignition position II.
  3. The service reminder indicator (SRI) should start flashing when you press the reset button for the trip odometer for about 10 seconds.
  4. Release the reset button for the trip odometer within 5 seconds.
  5. If you do not release the reset button for the trip odometer within 5 seconds, the indicator will not reset and the indicator will stop flashing.
  6. The instrument gives an audible signal when resetting has succeeded.

XC90 from MY2002 Service Light Reset

  1. Turn key to Ignition position I.
  2. Press and hold the reset button for the trip odometer.
  3. Turn to Ignition position II. Do this within 2 seconds.
  4. Hold the reset button on the trip meter pressed in until the original value has been reset. 
  5. For all vehicles from the 2003 model year, a general yellow lamp will light when you need to release the reset button.
  6. Release the reset button for the trip odometer within 4 seconds. The instrument gives an audible signal when resetting has succeeded.
  7. If you do not release the reset button for the trip odometer within 4 seconds, the service reminder indicator (SRI) will not reset.
  8. If the trip meter is already reset, hold the reset button for a minimum of 10 seconds and a maximum of 14 seconds. 

MY2011 XC90 Service Light Reset

  1. Turn the key to Ignition position I.
  2. Press and hold the reset button for the trip odometer.
  3. Turn to Ignition position II. You should do this within 2 seconds.
  4. Hold the reset button for the trip meter pressed in until the original value has been reset and the general yellow lamp comes on.
  5. Release the reset button for the trip odometer within 4 seconds. The instrument gives an audible signal when resetting has succeeded.
  6. Release the reset button for the trip odometer within 4 seconds to reset the service.
  7. If the trip meter is already reset, hold the reset button for a minimum of 10 seconds and a maximum of 14 seconds to complete the process.“

Toyota

Corolla 2000 to 2009 Service Light Reset

  1. Turn the ignition ON without starting the engine.
  2. Set the display window to ODO TRIP.
  3. Turn the ignition switch OFF.
  4. Press and hold TRIP ODOMETER RESET button. Turn the ignition to the ON position again while pressing the button (keep pressing for at least 5 seconds).
  5. Release the Trip Odometer Reset button after “MAINT REQD” flashes on the trip odometer display and the maintenance light turns off.
  6. Turn off the engine. Reset procedure is complete.

Corolla 2010 to 2020 Service Light Reset

  1. Turn the ignition ON (but do not start the engine) or press The “ENGINE START STOP” button two (2) times to enable the ACCESSORY MODE.
  2. Press the ODO/Trip button to display TRIP A.
  3. Turn the power OFF.
  4. Hold ODO/Trip Reset button, then press the “ENGINE START STOP BUTTON” twice or turn the ignition to ON position only.
  5. Do not release the ODO/TRIP Button until the RESETTING OIL MAINTENANCE DATA or “000000” is displayed.
  6. Turn Ignition OFF. Service Maintenance is complete.

Hilux 2004 to 2015 Service Light Reset

  1. Turn the ignition ON, but do not start the engine.
  2. Press the ODO/TRIP BUTTON to display to TRIP A. (Note: If TRIP A did not work, please display to ODO)
  3. Turn ignition OFF.
  4. Press and hold ODO/TRIP BUTTON and turn ignition to “RUN” position.  “000000” is displayed
  5. Turn the ignition OFF. Maintenance reset is complete.

Hilux 2004 to 2015 Service Light Reset

  1. Turn the ignition ON, but do not start the engine.
  2. Press the ODO/TRIP BUTTON to display to TRIP A. (Note: If TRIP A did not work, please display to ODO)
  3. Turn ignition OFF.
  4. Press and hold ODO/TRIP BUTTON and turn ignition to “RUN” position.  “000000” is displayed
  5. Turn the ignition OFF. Maintenance reset is complete.

Hilux 2015 to 2020 Service Light Reset

  1. Push the start button (Accessory mode). Do not start the engine.
  2. Press the ODO/TRIP BUTTON to display to TRIP A.
  3. Turn ignition OFF.
  4. Press and hold ODO/TRIP BUTTON and push the START BUTTON to accessory mode. Hold ODO/TRIP BUTTON for at least five (5) seconds until “RESETTING OIL MAINTENANCE DATA” is Complete or  “000000” Is Displayed.
  5. Turn the ignition OFF. Maintenance reset is complete.

Rav4 2020 Service Light Reset

  1. Put your key in the RAV4’s ignition. Turn it to position one. For clarification, position one is the position before starting the car.
  2. Push and hold the trip meter reset button on the dashboard. Turn your key to position two.
  3. Hold the odometer button for ten seconds. Your RAV4’s light should flash, perhaps beep, and then go out.
  4. Once the light goes out, release the odometer button and start the car.
  5. If you notice the light is still on, repeat this process one or two more times. That way, you know you’ve successfully reset the maintenance light on your Toyota RAV4.

Landcruiser Service Light Reset

  1. Turn your ignition key to the ‘ACC’ or ‘LOCK’ position.
  2. Press and hold the trip meter reset knob (next to your Toyota Land Cruiser’s odometer).
  3. While holding the trip meter reset knob, turn the ignition to ‘ON’. However, do not start your car just yet. 
  4. Hold the meter reset until the MAINT REQD light switches off.

Camry Service Light Reset

  1. Put your key in the ignition and turn it to position one (the first setting before actually starting the car).
  2. Quickly push and hold the odometer button on your dashboard, then turn your key to position two.
  3. Continue to hold the odometer button for about 10 seconds. The maintenance light should start to flash, and you may hear a beeping sound. Then the light should go out.
  4. Once the maintenance light is off, let go of the odometer button, and turn the key to start your car. The light should be off once your Camry starts. If it’s still on, repeat this process once or twice more to turn off the maintenance light on the Toyota Camry.

CH-R 2018 to 2020 / IZOA Service Light Reset

  1. Push the Start Button to ACCESSORY MODE.
  2. Press The TRIP BUTTON To Display To TRIP A.
  3. Then Turn The IGNITION To OFF.
  4. Press And Hold TRIP BUTTON And PUSH START BUTTON TO ACCESSORY MODE.
  5. Hold TRIP BUTTON For At Least 5 Seconds Until “RESETTING MAINTENANCE DATA” is complete.
  6. Turn The Ignition OFF. Maintenance Reset Is Complete.

Kluger/Highlander Service Light Reset

  1. Turn the ignition switch to the “On” position but do not crank the engine.
  2. Press the odometer button until the total mileage shows on the display.
  3. Turn the ignition switch off.
  4. Press and hold the odometer button. Turn the ignition on again.
  5. Release the odometer button when the maintenance required light blinks a few times then disappears.

Yaris 2005 to 2020 / Echo 1999 to 2005 Service Light Reset

  1. Turn the ignition ON.
  2. Press the ODO/TRIP button to display (TRIP A)
  3. Then, turn the ignition OFF.
  4. Now, hold and press the ODO/TRIP button and turn the ignition to ON. 
  5. Don’t release the ODO/TRIP BUTTON until the MAINT REQD warning light flashes multiple times and the light will disappear or “000000” appears.
  6. Turn ignition OFF. Maintenance required reset is complete.

Kia

Cerato 2016+ Service Light Reset

  1. Turn the ignition on but do not turn on the engine.
  2. You will see “Service Required” warning on the screen.
  3. If you don’t see this message, just press the ❏ (MODE) button on the steering wheel  until you see the message.
  4. Hold the ENTER button for a few seconds and release it once you see the “Hold ENTER: Reset”
  5. Hold the ENTER button again for a few seconds. Now you can see the service is reset.
  6. Turn the ignition off.
  7. Turn the ignition on again. You should see that the service details are reset.
  8. If you need to edit the service details, press the ❏ (MODE) button until you reach the ⚙️ (USER SETTINGS) icon. 
  9. Scroll down until you reach the Service Interval option. Edit the details using the MENU, BACK and ENTER buttons.
  10. Once done, turn the ignition off and on again. 

Seltos 2021 Service Light Reset

  1. Place the ignition to the ON position without starting the engine. If your vehicle has the keyless starting system, press the ENGINE START/STOP button twice without pressing the brake pedal.
  2. Go to the ⚙️ USER SETTINGS mode by pressing the ❐ MODE button repeatedly. The button is on the steering wheel.
  3. Find and select SERVICE INTERVAL. Use the navigation switch to scroll and press OK button to enter the menu.
  4. Make sure you activate the service interval function by giving a checkmark. In this menu, you can set a maintenance reminder at a specific interval by adjusting the Time or Distance. 
  5. Use the navigation switch to change the digit value. Press the OK button to confirm the changes.

Sportage 2011 to 2020 Service Light Reset

  1. Close all doors. Gear to the park position.
  2. Turn the ignition on. Don’t start the engine.
  3. Press the MENU button to navigate the SPANNER symbol to display the SERVICE REQUIRED.
  4. While the SERVICE REQUIRED is displayed, press and hold the OK button to reset the SERVICE to the next service interval schedule.
  5. Turn off the Ignition.

Hyundai

i30 2015 to 2017 Service Light Reset

  1. Turn the ignition key to the “ON” position without starting the engine
  2. If your vehicle has an ignition button, press the ENGINE START/STOP button twice without touching the brake pedal.
  3. Press the TRIP button repeatedly until you see USER SETTINGS menu. The button is on the steering wheel.
  4. Once you on the USER SETTINGS screen, press and hold the TRIP button to enter the menu.
  5. Press the TRIP button until the screen changes.
  6. Scroll down and select SERVICE INTERVAL On this menu, you can activate the service interval function.
  7. With this, you may adjust the time and distance at a specific interval.
  8. Turn the ignition off and then start the engine to verify the indicator has been reset.

Tucson 2016 to 2017 Service Light Reset

  1. When you turn on the engine and see “Service required” on the screen, press the OK button on the steering wheel for over 1 second.
  2. With this, the service interval will be reset to default settings. But you have to activate and set the service interval feature by accessing the SERVICE INTERVAL menu.
  3. To access the SERVICE INTERVAL menu, press the ❏ (MODE) button repeatedly until you see ⚙️ (USER SETTINGS). You can see these buttons on the steering wheel.
  4. Scroll down and select SERVICE INTERVAL. Press the OK button to access the menu.
  5. On this menu, you can activate the service interval function. If the service interval menu is activated, you may adjust the time and distance at a specific interval.
  6. Use the directional keypad to turn on the SERVICE INTERVAL mode and set the applicable interval.
  7. Turn the ignition off and then start the engine to verify the indicator has been reset.

Kona 2017 to 2020 Service Light Reset

  1. Close all doors, gear to the park position.
  2. Start the engine.
  3. Press the MODE button to navigate USER SETTINGS.
  4. Then scroll down to SERVICE INTERVAL. Press OK.
  5. Press the OK button while the spanner light is displayed.
  6. Select YES to confirm the reset, then press the OK button.
  7. The SERVICE INTERVAL is now reset to the new SERVICE INTERVAL SCHEDULE.
  8. Turn ignition off.

Accent 2018 to 2020 Service Light Reset

  1. Turn the ignition on, don’t start the engine.
  2. Press the PAGE button to navigate SETTINGS.
  3. Then scroll down to navigate SERVICE INTERVAL.
  4. Press the OK button to access SERVICE INTERVAL.
  5. Scroll down to navigate RESET then press the OK button
  6. Select YES then press the OK button to confirm the reset.
  7. Turn the ignition off. Service Maintenance Reset is complete.

Mitsubishi

Triton/Strada/L200 2005 to 2020 Service Light Reset

  1. Turn the Ignition OFF.
  2. Press the TRIP BUTTON until the SPANNER/WRENCH LIGHT appears.
  3. Press and hold the TRIP BUTTON until the spanner light flashes on the screen.
  4. Release the TRIP BUTTON and press it again. It will display CLEAR.
  5. Press the TRIP BUTTON one more time.
  6. Wait a second until the new interval appears.
  7. Start the engine to verify if the service reminder was reset.

ASX 2010 to 2020 Service Light Reset

  1. Turn Off the Ignition.
  2. Press the INFO BUTTON.
  3. Continue to press the INFO BUTTON until the Wrench Service Light appears.
  4. Press and hold the INFO Button until the Wrench Light start flashes. 
  5. Then, release the INFO BUTTON to display CLEAR.
  6. Press again the INFO button to reset the Service Maintenance Reminder Light.
  7. Start the engine to verify the service reminder indicator was reset.

Outlander 2006 to 2020 Service Light Reset

  1. Turn off the ignition.
  2. Press the INFO BUTTON until the Wrench-Miles-Month appears. (Note: some info button is on the right side of the instrument panel)
  3. Press and hold the INFO BUTTON until the wrench symbol flashes.
  4. Release and press the info button again and the CLEAR message appears.
  5. Wait for 2 seconds until you set the new service maintenance schedule.
  6. Service maintenance reminder is complete. Start the car to verify if the service reminder was reset.

Lancer 2007 to 2017 / Galant Service Light Reset

  1. Put the ignition to the first position.
  2. Press the INFO BUTTON until the SPANNER service light appears
  3. Then press and hold the INFO BUTTON until the spanner light flashes.
  4. Press the INFO button again until “CLEAR” appears on the display
  5. Start the Engine to verify if the service maintenance reminder was reset.

Magna TJ 2001 to 2003 Service Light Reset

  1. Turn Ignition to “Lock” position.
  2. Press and hold the UP button of the mode switch and turn the ignition ON.
  3. The light will then flash for 10 seconds and then turn the ignition off

Mazda

CX-5 2012 to 2020Service Light Reset

  1. Press your finger against the push-button start button. Do this twice, ensuring you have released your foot from the brake.
  2. Go to your touchscreen and search through the MAZDA CONNECT™ infotainment applications menu.
  3. Select “Vehicle Status Monitor” from the application menu.
  4. Click “maintenance” and then navigate to “Oil Change.”
  5. From there, tap the “Reset” button from the oil change menu. After this, the light should begin resetting.

Mazda 3 2003 to 2020 Service Light Reset

  1. Press and hold the TRIP BUTTON with the ignition switched off.
  2. Then switch it on to Accessory Mode.
  3. Keep pressing the selector for over 5 seconds.
  4. The master warning light will flash for a few seconds when the reset is completed.

CX-3 2015 to 2020 Service Light Reset

  1. Turn the ignition key to “ON” position without starting the engine. If your vehicle has a Smart key button, press the START-STOP ENGINE button twice without touching the brake pedal.
  2. Tap the APPLICATION menu on the touch screen. The touch screen is on the centre dash.
  3. Tap the touch screen to enter the menu and select VEHICLE STATUS MONITOR.
  4. Then select MAINTENANCE.
  5. Scroll and select SCHEDULED and then select RESET.
  6. When a confirmation dialog appears, select “YES” to confirm.
  7. Next, go back to the MAINTENANCE menu and select OIL CHANGE to reset the engine oil data. You must reset the engine oil data after performing the engine oil change on your vehicle.
  8. Select RESET and select “YES” to confirm.

CX-30 2020 to 2021 Service Light Reset

  1. Place the ignition to the ON position without starting the engine. If your vehicle has the keyless starting system, press the ENGINE START/STOP button twice without pressing the brake pedal.
  2. From the main menu, select INFORMATION. Use the control button on the centre console or tap the screen if equipped with the touchscreen.
  3. Go to VEHICLE STATUS MONITOR. Several menu options will appear on the screen.
  4. Select VEHICLE MAINTENANCE SETTINGS. In this menu, you can set the service reminder at a specific interval by adjusting the NEXT SERVICE DATE or NEXT SERVICE DISTANCE, or you can also select RESET OIL CHANGE DISTANCE.
  5. Select one menu and follow the instructions on the screen.

Volkswagen

Golf 2008 to 2020 Service Light Reset

  1. Turn OFF the ignition. 
  2. Press and hold the 0.0 button.
  3. While holding the 0.0 Button, turn the ignition ON. Don’t release the 0.0 button until the “RESET OIL CHANGE SERVICE” message appears.
  4. While the “RESET OIL CHANGE SERVICE” is displayed, release the 0.0 button, then press again the 0.0 button to reset the service reminder.
  5. Turn Ignition off, when “SERVICE WAS RESET” message disappears.

Honda

Civic 2000 to 2005 Service Light Reset

  1. Close all doors, gear to the park position.
  2. Make sure the ignition is off. Press and hold the TRIP button and don’t release.
  3. While pressing and holding the TRIP button, turn the ignition to ON position, continue to hold the TRIP button until the MAINTENANCE REQUIRED light disappears.
  4. Turn off the ignition, maintenance required light reset is complete.

Civic 2006 to 2011 Service Light Reset

  1. Close all doors, gear to the park position.
  2. Turn the ignition on but don’t start the engine.
  3. Press the RESET button until the OIL LIFE appears.
  4. Press and hold the RESET button until the A1 OIL LIFE flashes.
  5. Release the TRIP button, then press and hold again until the OIL LIFE is reset to 100%.
  6. Turn off the ignition, oil reset is complete.

Civic 2011 to 2015 Service Light Reset

  1. Close all doors, gear to the park position.
  2. Turn the ignition on. Don’t start the engine.
  3. Press the INFO button to clear the screen.
  4. Press the MENU button, then scroll to VEHICLE INFORMATION, then press the SOURCE/OK button.
  5. Then, once the MAINTENANCE INFO appears, press the SOURCE/OK button.
  6. Select OIL AND FILTER, then press the SOURCE/OK button.
  7. Select YES in MAINTENANCE INFO, then press the SOURCE/OK button.
  8. MAINTENANCE INFORMATION HAS BEEN RESET. Turn off the ignition MAINTENANCE RESET is complete.

Civic 2016 to 2020 Service Light Reset

For Models With Multi-Information Screen:

  1. Turn your Civic ignition on, but do not start the engine. If your vehicle is a push start, press the push start button twice without putting your foot on the brake pedal.
  2. Press the Info button on the steering wheel until the wrench icon appears on the screen.
  3. Press and hold the enter button to enter reset mode.
  4. Use the up and down arrows, select “All Due Items,” and press enter.

For Models Without Multi-Information Screen:

  1. Turn your Civic ignition on without starting your engine or press the start button twice without touching the brake.
  2. Press the trip knob repeatedly until the Engine Oil Life percentage displays.
  3. Hold the trip knob until the Engine Oil Life percentage blinks.
  4. Press the trip knob again until the oil life percentage resets.

Turn on your Honda Civic after completing these steps to verify the reset was successful.

CR-V 2001 to 2006 Service Light Reset

  1. Turn off the engine.
  2. Press and hold the Select/Reset button on the instrument panel, then turn the ignition switch to the ON (II) position.
  3. Hold the button for about 10 seconds until the indicator goes off.

CR-V 2007 to 2021 Service Light Reset

Option 1

  1. Turn the ignition to the first position. Do not start the engine.
  2. Press the “Trip” stem to toggle it to show “Engine Oil Life“.
  3. Hold the “Trip” stem for about 10 seconds until the display starts blinking. Once blinking, release the “Trip” stem.
  4. Turn/twist the “Trip” step to choose the “Reset” option.
  5. Press and hold the “Trip” stem again, this time for 5 seconds. The Oil Life will reset to 100%.

Option 2

  1. Turn the ignition to the first position. Do not start the engine.
  2. Press the “i” on the steering wheel to toggle over to “Maintenance Minder“.
  3. Press “Enter” to select “Maintenance Minder” (wrench icon).
  4. Hold “Enter” for about 10 seconds until it enters Reset Mode.
  5. Scroll to “Engine Oil Life“, then press “Enter“.

Option 3 (Touchscreen Models)

From the Home screen, choose “Settings” > “Vehicle” > “Maintenance Info” > “Select Reset Items” > “Engine Oil Life”

Isuzu

D-Max 2012 to 2020 Service Light Reset

  1. Turn the ignition key to the “ON” position without starting the engine. If your vehicle has an ignition button, press the Engine Start/Stop button without touching the brake pedal.
  2. Go to SELECT MODE by pressing the INFO button repeatedly. The button is on the wiper lever.
  3. If you are already on the screen, press and hold the INFO button for several seconds. Press and hold the INFO button to enter the menu.
  4. Scroll and select the SERVICE menu. Use the INFO button to scroll and select.
  5. Select the service item you want to reset (i.e. ENGINE OIL or MAINTENANCE). This menu lets you set a reminder at a specific interval.
  6. Select END to exit settings. If you have finished setting the date and distance of the reminder, select END to exit
  7. Turn the ignition off and start the engine to verify the indicator has been reset.

Forester 2014 Service Light Reset

Subaru

  1. Turn the ignition to run (one position before starting engine).
  2. Using the controls on the left-hand side of the steering wheel. Pull the i/Set button towards you to bring up the selection screen.
  3. Use the Up or Down arrow to highlight the MAINTENANCE menu and pull the i/Set switch towards you.
  4. Select the maintenance item (i.e. Engine Oil, Oil Filter) and pull the i/SET switch towards you.
  5. Change the next service date and interval with the Up and Down arrow and confirm by highlighting SET and pull the i/SET switch towards you. The reset is complete when the screen shows Setting Complete.
  6. Turn the ignition off and then start the engine to verify the indicator has been reset.