Land rover diagnostic tool & Jaguar diagnostic tool
The Land Rover & Jaguar OBD2 Scan Tool is an easy to use, stand alone unit that will have you scanning your vehicle like a pro within minutes. Simply, plug it into the OBD II port and the device will boot up with step-by-step instructions. This scanner has a large, easy to read colour display accompanied by a user friendly interface that requires no additional software.
This scanner will allow you to access ALL Land Rover & Jaguar* vehicles systems including engine, transmission, ABS/DSC, Airbag, Body systems, etc. You will be able to read/reset Land Rover & Jaguar specific codes as well as read live data from vehicle systems. As an added bonus, the scanner is equipped with full OBDII capabilities that allow you to scan all engine readings and related trouble codes (check engine light) on ANY vehicle make/model 2005+*.
OBD2 Functions Include*:
1. Read Codes
2. Erase Codes
3. I/M Readiness — I/M Readiness indicates whether or not the various emissions-related systems on the vehicle are operating properly and are ready for Inspection and Maintenance testing.
4. Data Stream
5. Freeze Frame — When an emission-related fault occurs, certain vehicle conditions are recorded by the on-board computer. This information is referred to as freeze frame data. Freeze Data is a snapshot of the operating conditions at the time of an emission-related fault.
6. O2 Sensor Test — This option allows retrieval and viewing of O2 sensor test results for most recently performed tests from the vehicle’s on-board computer.
7. On-Board Monitoring — This function can be utilised to read the results of on-board diagnostic monitoring tests for specific components/systems.
8. Evap System Test — The EVAP test function lets you initiate a leak test for the vehicle’s EVAP system. Before using the system test function, refer to the vehicle’s service repair manual to determine the procedures necessary to stop the test.
9. Vehicle Information — The option displays the vehicle identification number (VIN), the calibration verification number (CVN), and other information of the test vehicle.
10.Retrieve generic (P0, P2, P3, and U0), manufacturer specific (P1, P3, and U1) codes and pending codes
11.Turn off Check Engine Light (MIL), clear codes and reset monitors
12. Read live PCM datastream
13. Support CAN (Controller Area Network) and all other
14.Multilingual menu and DTC definitions- English, Spanish, and German, etc
15.Read pending DTCs
16.Read permanent DTCs
17. DTCs search
Special FUNCTIONS for Land Rover & Jaguar*:
Oil/Service/Brake Service Reset Function*
Reset the engine oil, Carry out the CBS Reset, Exhaust emission inspection, Coolant Service Reset, Spark plugs Reset, Brake fluid Service Reset, Micro-filter Service Reset
Battery Check and Registration*
Register the battery replacement, this is a MUST DO JOB, failing to do so may create an over charging situation, shorten the battery life and/or enable limp-home mode
EPB Reset Function*
Brake Pad / Shoe changes on vehicles equipped with EPB’s (Electronic Parking Brakes) MUST be carried out using a Diagnostic Tool to correctly re-calibrate. This tool will offer you that capability on supported models. De-activate to Service Position – Replace – Re-activate.
SAS Reset Function*
The Steering Angle Sensor (SAS) is used to measure the angle of the steering wheel and the speed at which it is being turned. The signal is mainly used by the ABS System as part of it’s stability control function but also by other systems such as ride level control and adaptive lighting. A problem with the SAS Signal will cause a fault with any of the systems that use the signal directly, or indirectly.
If the Steering Angle Sensor (SAS) needs to be changed, many vehicle’s require the new sensor to be calibrated. This tool will allow you to carry out steering angle re-calibration on supported models.
DPF Regeneration or Replacement*
Carry out a forced Diesel Particulate Filter (DPF) Regeneration on supported vehicles – this MUST be done by trained personnel. Required when the DPF filter blockage reaches levels where passive or active regeneration is unable to burn off the excess soot.
Diagnose ABS/SRS system codes, read and clear DTCs and turn off ABS/SRS warning light, retrieves ABS/SRS ECU information, etc.
Main Unit, OBD 16PIN Cable, User Manual, USB Cable, Protective Nylon Case.
NOTICE: PRODUCT LIMITATIONS
*Some features may not be available on some models and makes. Please get in touch with us first to ensure compatibility when in doubt. A special software update is and may be required to enable some features and functions. The software update is available in Windows only. Video and photo proof is required for any claim of this product as not working. The video proof must clearly show and demonstrate the claim. Returns and refunds due to incompatibility (without or against OBD2 Australia advise, or refusal to execute troubleshooting/provide the required proof) will be subject to our Returns Policy/Terms.